WALL ANTI-GRAFFITI is a two-component product that, after mixing, cures at room temperature under the influence of ambient moisture.
WALL ANTI-GRAFFITI makes wall surfaces easy to clean from graffiti and poster residues.
The dual system consists of silicone and a washable layer. The triple property of this dual system is that it is washable, water-repellent and breathable.
When washing, the contaminated washing water is drained by the system. Since washing must be done with a cold water, high-pressure washer (max. 100 bar), the surface does NOT need to be re-treated against graffiti after washing.
Applicable:
- brick, cotto
- concrete
- mortar, plaster
- sand-lime brick
- limestone
- polished granite, - marble
- painted wood
- painted aluminum
- painted metal
- epoxy resin
graffiti removal |
translucent coating |
easy removal of poster residues |
Always do a test treatment!
The material is characterized by high UV resistance, excellent sun protection, heat resistance, breathability and durability.
Recommended for the protection of buildings regularly affected by flooding!
You can order here: 
Storage:
In its original, closed container, or even in diluted form, between 0-30 oC, away from sunlight, it can be stored for at least 12 months from the date indicated on the label. If the product's shelf life has expired, the material may still be good, which must be confirmed by a preliminary test.
Application:
WALL ANTI-GRAFFITI must be mixed on site before use. Then, the semi-finished product (“Component “A”) is mixed with the white spirit with additives (“Component “B”) and, if necessary, the coloring agent and/or matting agent.
Ready-mixed WALL ANTI-GRAFFITI is a solvent-based preventive protective agent. WALL ANTI-GRAFFITI can be applied using industrial spraying methods, such as airless spraying equipment and/or a conventional roller, using appropriate protective equipment.
For appropriate protective equipment, see the Safety Data Sheet.
Only airless spraying equipment (e.g. screw pump) can be used to apply ready-mixed WALL ANTI-GRAFFITI, but it can also be applied with a brush or teddy roller on smaller surfaces.
Due to its consistency, it can be applied in a single layer.
After use, tools and equipment must be rinsed immediately with solvents (e.g. white spirit) to prevent the material from crosslinking and the formation of a hard, sticky film that can cause clogging.
The surface to be treated must appear dry to the eye.
Only WALL ANTI-GRAFFITI PRIMER is suitable for priming!
Primer is required when applying to painted surfaces, very smooth, shiny surfaces (gress, marble, polished stone), metal or plastic!
Only WALL ANTI-GRAFFITI primer is suitable for priming!
When applied in one layer, ready-mixed WALL ANTI-GRAFFITI quickly sets on a dry surface due to the humidity of the air. The setting occurs first on the surface and over time also in the surface, due to the ambient moisture available in the capillaries.
Total drying time: 24 hours.
Consumption depending on the absorbency of the surface: 0,25-0,4 l/m2.
Always perform a test treatment on the surface to be treated!
This way we can calculate and check, for example, the desired amount of material or the effectiveness of the agent.
The surface treated with ready-mixed WALL ANTI-GRAFFITI will be completely transparent and shiny. If you mix a matting agent, it will be less visible on the surface.
Mixing ratios:
The material mixed with the matting agent must be used, it cannot be stored!
Pot life: approx. 20 minutes at 25 oC.
The material that has already been mixed and not used can only be stored for a short time if it can be sealed airtight and before sealing it is filled with nitrogen gas to exclude air.
WALL ANTI-GRAFFITI can also be colored.
For example:
- Using 4% CAPAROL Titandioxid Crimea 271, we can give the surface to be treated a white color.
- Using 4% CAPAROL PPZU Blau 04, we can give the surface to be treated a blue color.
- Using 4% CAPAROL PPZU Rot 10, we can give the surface to be treated a red color
The color saturation on the surface to be treated can be controlled by the amount of material applied. (150 g/m2 - 450 g/m2)
mattifying agent vs. without mattifying agent (click on the image)
Anti-Graffiti + pigment + 2% matting agent (click on the image)
Caution: Use on monuments or buildings of a historical or historical nature only at your own risk.
Attention: The surface to be treated must not be overheated!
Treatment temperature: 5-30 oC.
If a skin has formed during storage, it must be thrown away from the surface.
Graffiti removal:
Clean the contaminated surface with a cold water, high-pressure washing device (max. 100 bar). After cleaning, the protective layer does NOT need to be reapplied!
The system can withstand up to 16 washing cycles.
The effect of Wall Anti-Graffiti - Washing off graffiti
Safety measures:
The "Safety Data Sheet" can be obtained from the manufacturer or the dealer.
Safety Data Sheet reach
|
|